Shop by Brand, Category or Keyword

Cirr D Bond: 5-Gallon Pail
$477.82
Made by Global Specialty Products. This is a product that metal parts can be submerged in and will help take off crystallized iso and cured foam. (can be heated to a maximum of 150F). Available in a 5-gallon pail or 1-gallon jug.

Dynasolve CU-6 1g
$161.78

Dynasolve CU-6is a non-gelling, higher flash point version of CU-5, and is recommended for both flushing and cleaning, especially in applications in which liquid isocyanates are present either prior to cleaning, or will be introduced after cleaning (such as in a mixing tank).Dynasolve CU-6is non-chlorinated, nonflammable (by U.S. Department of Transportation definition), non-carcinogenic, and non-ozone depleting. It replaces and improves on the performance of commodity solvents such as methylene chloride, acetone, methyl ethyl ketone (MEK), and 1,1,1-trichloroethane.Dynasolve CU-6can be used for extended periods, tolerate high resin loadings, and will reduce disposal costs. It is also recyclable via vacuum distillation.

Directions for Use

1. For Flushing: UseDynasolve CU-6as you would normally use any other flushing solvent. Mild heating of the solvent will product faster results. The use of compressed air for agitation of the solvent will also help to facilitate cleaning. If excessive amounts of liquid isocyanates are present, Dynasolve Iso-Neutralizer must be used first. Failure to use the Iso-Neutralizer may lead to gelling of the flushing solvents.
2. For Cleaning: Immerse parts to be cleaned inDynasolve CU-6. Let soak until residue is loosened and can be wiped or brushed off. Then rinse parts with water and dry. Mild heating of the solvent to 130-150° F, and/or the use of ultrasonics will produce faster results. Mechanical filtering of larger urethane particles using a cheesecloth or metal mesh filter will help extend the life of the solvent. For the most difficult applications, more aggressive (reactive) solvents are available. Please contact Dynaloy for more information on these products.

Materials of Construction

Materials of Construction
Recommend: Teflon, butyl rubber, silicon rubber, Kalrez, mild steel, Halar, melamine, Nylon 101, polyethylene, polypropylene, Ryton (150°F or less).
Avoid: Viton, PVC, ABS, Buna-N, Durel, Hypalon, Kynar, Lexan, Lucite, Neoprene, Noryl EN-265, Noryl 731, PET, phenolic, polyester, polysulfone, polyurethane, Ultem, Valox.

Cautions

Dynasolve CU-6contains powerful organic solvents. It is harmful if inhaled or swallowed. Avoid breathing vapors or mist. Keep away from heat and flame. Avoid contact with eyes and skin. Wear gloves, safety glasses, and protective clothing when handling. Use with adequate ventilation.

  •  Dynasolve CU-6 is especially effective for flushing mixing and metering equipment and feed lines, as it quickly and completely cleans polyols, crystallized isocyanates, and other urethane intermediates. However, in cleaning of isocyanate sides of equipment, Dynasolve  Iso-Neutralizer should be used first if excessive onlyamounts of liquid isocyanates are present. Dynasolve CU-6 will not gel in contact with liquid isocyanates, but if limited amounts are present.
  •  Dynasolve CU-6 is very effective in penetrating, loosening, and removing cured urethane foam deposits andbuild-up from mixing heads, troughs, conveyor parts, side walls, rollers, foam cutting devices and molds.
  •  Dynasolve CU-6 will remove all types of urethanes: flexible, rigid, elastomers, molded, and adhesives. It iseffective for both MDI and TDI esters and ethers.
  •  Dynasolve CU-6 will quickly and completely clean residual cured polyurethane reactive hot melt (PURHM)urethane adhesives from roll coating equipment. It will also remove these same reactive hot melts fromdispensing equipment.
  •  Dynasolve CU-6 is excellent for the removal of polymer-based inks from rollers in flexographic printingequipment.
  •  When heated, Dynasolve CU-6 will also clean many types of epoxies and other adhesives.



Glycol Ether Gun Cleaner 1 gallon
$28.00


Gun Cleaner Effective for Soaking Gun Parts and Removing Isocyanate and Resin Liquids

 Sold in 1 gallon containers

Spray Foam Equipment and Parts distributed by Profoam Corporation in Rutledge, GA, near Atlanta. Ships anywhere. Call 706-557-1400.


GSP Surf A Lube: 1-Gallon Jug
$75.43
Made by Global Specialty Products. This is used after flushing lines with NZD ISO Flush or Surf X Flush for storage of pumps and equipment. Can stay in the lines up to 24 months and is completely recyclable. Available in a 5-gallon pail or 1-gallon jug.

GSP Surf A Lube: 5-Gallon Pail
$325.83
Made by Global Specialty Products. This is used after flushing lines with NZD ISO Flush or Surf X Flush for storage of pumps and equipment. Can stay in the lines up to 24 months and is completely recyclable. Available in a 5-gallon pail or 1-gallon jug.

GSP Surf X Flush: 1-Gallon Jug
$94.85
Made by Global Specialty Products. Can be used daily for over spray and cleaning and also can be used to flush out lines. This product must not be left overnight. It will need to be chased out with ISO/Resin or with Surf A Lube for storage. Available in a 5-gallon pail or 1-gallon jug. This product also comes in Go Green Wipes - 90 sheets.

GSP Surf X Flush: 5-Gallon Pail
$365.62
Made by Global Specialty Products. Can be used daily for over spray and cleaning and also can be used to flush out lines. This product must not be left overnight. It will need to be chased out with ISO/Resin or with Surf A Lube for storage. Available in a 5-gallon pail or 1-gallon jug. This product also comes in Go Green Wipes - 90 sheets.

GSP Surf X Flush: Go Green Wipes
$60.00
Surf X Flush 2000- Go Green Wipes
  •  90 Sheets 12x12
  •  Daily Cleaning/Overspray

TSL-Throat Seal Liquid/Pump Lube, 1 Gallon
$75.99

Throat Seal Liquid (TSL) prevents paint and coatings from drying onto the displacement rod and packings, extending the life of the pump.

Sold in 1 gallon Jug


Spray Foam Equipment and Parts distributed by Profoam Corporation in Rutledge, GA, near Atlanta. Ships anywhere. Call 706-557-1400.


Tytan Professional Can Foam Cleaner 00799
$9.00

A multi-use product designed for removing uncured polyurethane foams or adhesives. It is useful for cleaning of can valves and PU-foam gun applicators. The cleaner is excellent for degreasing metal surfaces before application of silicones and polyurethane. The Cleaner is manufactured in compliance with requirements of ISO 9001:2008 standard.

  •  Gun & Spray Nozzle
  •  Removes Uncured Foam
  •  Clear in Color
  •  12-oz Can
  •  Sold Individually

 Dissolving only uncured one-component PU-foams and adhesives. Cleaner has a destructive effect on the polystyrene, PVC and some other plastics, before use, test the cleaner on a given surface.


Urethane Mold Release-1 Can
$9.99

Stoner Urethane E236 Mold Release from is specially formulated as a release agent and anti-stick lubricant for molded urethanes. A light coating produces best results. E236 Mold Release provides fast, easy partial removal from molds and multiple part releases per application. Improves molding efficiency in many processes, including injection, compression, transfer, vacuum form, pour cast, die cast, and extrusion molding. Stoner Mold Release is used to prolong the life of your molds and to aid in the ease of releasing your cast urethane parts. Stoner was formulated specifically for urethanes and is the ideal choice when casting urethane into a urethane mold.

  •  Specifically formulated as release agent and anti-stick lubricant for molded urethanes
  •  Provides easy removal from molds
  •  Excellent choice for multiple mold processes
  •  Prolongs the life of your molds
  •  12 oz aerosol spray can


Urethane Mold Release-12 cans/case
$104.85

Stoner Urethane E236 Mold Release from is specially formulated as a release agent and anti-stick lubricant for molded urethanes. A light coating produces best results. E236 Mold Release provides fast, easy partial removal from molds and multiple part releases per application. Improves molding efficiency in many processes, including injection, compression, transfer, vacuum form, pour cast, die cast, and extrusion molding. Stoner Mold Release is used to prolong the life of your molds and to aid in the ease of releasing your cast urethane parts. Stoner was formulated specifically for urethanes and is the ideal choice when casting urethane into a urethane mold.

  •  Specifically formulated as release agent and anti-stick lubricant for molded urethanes
  •  Provides easy removal from molds
  •  Excellent choice for multiple mold processes
  •  Prolongs the life of your molds
  •  12 oz aerosol spray cans/ 12 per case