Shop by Brand, Category or Keyword

Brake Cleaner-1 can
0
(0)
$4.13

Brake Parts Cleaner-14 oz can, 70 percent VOC,1 can


Brake Parts Cleaner; Non-Chlorinated; Removes oil, grease, brake fluid and contaminants quickly and with no residue. For use on all ABS, disc and Drum Brakes.

Brake Cleaner-12 per case
0
(0)
$49.54
Brake Parts Cleaner, 14oz cans, 70 percent VOC-12 per case

Brake Parts Cleaner; Non-Chlorinated; Removes oil, grease, brake fluid and contaminants quickly and with no residue. For use on all ABS, disc and Drum Brakes. 

Dynasolve CU-6 1g
0
(0)
$161.78

Dynasolve CU-6is a non-gelling, higher flash point version of CU-5, and is recommended for both flushing and cleaning, especially in applications in which liquid isocyanates are present either prior to cleaning, or will be introduced after cleaning (such as in a mixing tank).Dynasolve CU-6is non-chlorinated, nonflammable (by U.S. Department of Transportation definition), non-carcinogenic, and non-ozone depleting. It replaces and improves on the performance of commodity solvents such as methylene chloride, acetone, methyl ethyl ketone (MEK), and 1,1,1-trichloroethane.Dynasolve CU-6can be used for extended periods, tolerate high resin loadings, and will reduce disposal costs. It is also recyclable via vacuum distillation.

Directions for Use

1. For Flushing: UseDynasolve CU-6as you would normally use any other flushing solvent. Mild heating of the solvent will product faster results. The use of compressed air for agitation of the solvent will also help to facilitate cleaning. If excessive amounts of liquid isocyanates are present, Dynasolve Iso-Neutralizer must be used first. Failure to use the Iso-Neutralizer may lead to gelling of the flushing solvents.
2. For Cleaning: Immerse parts to be cleaned inDynasolve CU-6. Let soak until residue is loosened and can be wiped or brushed off. Then rinse parts with water and dry. Mild heating of the solvent to 130-150° F, and/or the use of ultrasonics will produce faster results. Mechanical filtering of larger urethane particles using a cheesecloth or metal mesh filter will help extend the life of the solvent. For the most difficult applications, more aggressive (reactive) solvents are available. Please contact Dynaloy for more information on these products.

Materials of Construction

Materials of Construction
Recommend: Teflon, butyl rubber, silicon rubber, Kalrez, mild steel, Halar, melamine, Nylon 101, polyethylene, polypropylene, Ryton (150°F or less).
Avoid: Viton, PVC, ABS, Buna-N, Durel, Hypalon, Kynar, Lexan, Lucite, Neoprene, Noryl EN-265, Noryl 731, PET, phenolic, polyester, polysulfone, polyurethane, Ultem, Valox.

Cautions

Dynasolve CU-6contains powerful organic solvents. It is harmful if inhaled or swallowed. Avoid breathing vapors or mist. Keep away from heat and flame. Avoid contact with eyes and skin. Wear gloves, safety glasses, and protective clothing when handling. Use with adequate ventilation.

  •  Dynasolve CU-6 is especially effective for flushing mixing and metering equipment and feed lines, as it quickly and completely cleans polyols, crystallized isocyanates, and other urethane intermediates. However, in cleaning of isocyanate sides of equipment, Dynasolve  Iso-Neutralizer should be used first if excessive onlyamounts of liquid isocyanates are present. Dynasolve CU-6 will not gel in contact with liquid isocyanates, but if limited amounts are present.
  •  Dynasolve CU-6 is very effective in penetrating, loosening, and removing cured urethane foam deposits andbuild-up from mixing heads, troughs, conveyor parts, side walls, rollers, foam cutting devices and molds.
  •  Dynasolve CU-6 will remove all types of urethanes: flexible, rigid, elastomers, molded, and adhesives. It iseffective for both MDI and TDI esters and ethers.
  •  Dynasolve CU-6 will quickly and completely clean residual cured polyurethane reactive hot melt (PURHM)urethane adhesives from roll coating equipment. It will also remove these same reactive hot melts fromdispensing equipment.
  •  Dynasolve CU-6 is excellent for the removal of polymer-based inks from rollers in flexographic printingequipment.
  •  When heated, Dynasolve CU-6 will also clean many types of epoxies and other adhesives.



Stoner Anti Stick Coating-1 Can
0
(0)
$11.99
Stoner Anti Stick Coating-1 Can-New & Improved Formula

Apply E238 anti-stick coating onto surfaces to prevent spray foam from sticking to treated equipment, window frames, pipes, and masked off work areas. Allows for easy removal of overspray. E238 is a specially formulated, durable, thin, anti-stick coating that prohibits polyurethane and other adhesives from bonding to treated surfaces.


Stoner Anti Stick Coating-12 cans/case
0
(0)
$130.99
Stoner Anti Stick Coating-12 cans/case-New & Improved Formula

Apply E238 anti-stick coating onto surfaces to prevent spray foam from sticking to treated equipment, window frames, pipes, and masked off work areas. Allows for easy removal of overspray. E238 is a specially formulated, durable, thin, anti-stick coating that prohibits polyurethane and other adhesives from bonding to treated surfaces.

Stoner B-505 Polyoff Polyurethane Remover, 1 gallon can
0
(0)
$199.00

Stoner B-505 Polyoff Polyurethane Remover, 1 gallon can

Extra powerful, time-saving formula cleans molds and tools with ease. Completely removes cured polyurethane, mold release, and other build-up from tooling, molds, and machinery. Use only on steel, aluminum and other metal tooling


TSL-Throat Seal Liquid/Pump Lube, 1 Gallon
0
(0)
$75.99

TSL-Throat Seal Liquid/Pump Lube, 1 Gallon

Throat Seal Liquid (TSL) prevents paint and coatings from drying onto the displacement rod and packings, extending the life of the pump.

  •  Sold in 1 gallon Jug

Spray Foam Equipment and Parts distributed by Profoam Corporation in Rutledge, GA, near Atlanta. Ships anywhere. Call 706-557-1400.